24V DC Worm Gear Correct Angle Brush Equipment Motor
Product Description:
Gear Motor-Torque Table Allowance Torque Device:Upside (N.m)/Belowside (kgf.cm)
•Gearhead and Intermediate gearhead are offered separately.
•Enter the reduction ratio into the blank() inside of the product title.
•The speed is calculated by dividing the motor’s synchronous speed by the reduction ratio. The true pace is two%~20% much less than the exhibited value, relying on the measurement of the load.
•To reduce the speed over and above the reduction ratio in the adhering to desk, connect an intermediate gearhead (reduction ratio: ten) between the reducer and motor. In that circumstance, the permissible torque is 8N-m.
|
Kind Motor/Gearhead |
Equipment Ratio |
3 |
three.6 |
5 |
6 |
seven.five |
nine |
12.five |
15 |
eighteen |
twenty five |
thirty |
36 |
50 |
60 |
75 |
ninety |
one hundred |
a hundred and twenty |
one hundred fifty |
a hundred and eighty |
|
Velocity r/min |
a thousand |
833 |
600 |
five hundred |
400 |
333 |
240 |
200 |
166 |
a hundred and twenty |
one hundred |
83 |
sixty |
fifty |
forty |
33 |
30 |
25 |
twenty |
16 |
|
| Z4D120-24GN(4GN25RC) |
4GN()RC/ 4GN()RT |
.twenty five |
.thirty |
.forty two |
.50 |
.70 |
.84 |
1.sixteen |
one.39 |
one.67 |
two.32 |
2.78 |
three.34 |
4.sixty four |
5.01 |
six.27 |
seven.fifty two |
8.00 |
eight.00 |
8.00 |
8.00 |
|
two.fifty five |
three.06 |
4.28 |
5.10 |
7.14 |
8.fifty seven |
11.eight |
14.2 |
17. |
23.7 |
28.4 |
34.one |
47.3 |
fifty one.1 |
sixty four. |
76.7 |
eighty. |
eighty. |
eighty. |
eight.00 |
Proportions(Device:mm):
Business Data
FAQ
Q: What’re your major items?
A: We at present generate Brushed Dc Motors, Brushed Dc Equipment Motors, Planetary Dc Equipment Motors, Brushless Dc Motors, Stepper motors, Ac Motors and Higher Precision Planetary Gear Box and so on. You can check the specifications for earlier mentioned motors on our website and you can email us to advise needed motors for each your specification also.
Q: How to pick a suited motor?
A:If you have motor pictures or drawings to demonstrate us, or you have thorough specs like voltage, speed, torque, motor size, functioning manner of the motor, essential life span and sounds stage and many others, you should do not wait to enable us know, then we can advocate suitable motor for every your ask for accordingly.
Q: Do you have a CZPT support for your normal motors?
A: Indeed, we can customize for each your ask for for the voltage, pace, torque and shaft dimensions/form. If you need extra wires/cables soldered on the terminal or need to have to insert connectors, or capacitors or EMC we can make it as well.
Q: Do you have an person layout support for motors?
A: Sure, we would like to layout motors individually for our clients, but it may possibly need some mildew developing value and design cost.
Q: What’s your direct time?
A: CZPTly talking, our typical common item will need 15-30days, a little bit for a longer time for CZPT items. But we are very flexible on the direct time, it will depend on the particular orders.
You should get in touch with us if you have in depth requests, thank you ()
